Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Cap & Crown in Taunton: What to Know First
We provide independent Olympia Chimney chimney cap and crown service in Taunton, with most jobs completed in a single visit and upfront pricing agreed before we start. A standard Olympia Chimney cap replacement runs $280-$520, while crown repair or coating typically falls between $340-$780 depending on flue count and access. We do not upsell what your chimney does not need, and every recommendation comes with photos you can see for yourself.
This page is for Taunton homeowners who already have an Olympia Chimney system installed and need honest answers about cap or crown problems. Whether you are in a 1980s split-level near Lake Sabbatia or a century-old colonial closer to Taunton Green, we have worked on your chimney type before. Call (774) 310-4281 to speak with a live person now, or read on for the specifics.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney stainless single-flue caps (SC-series): The mesh on the SC-8 and SC-10 models can clog with creosote faster than heavier-gauge competitors, especially in Taunton where oak and maple are common firewood choices and burn wetter than people realize. We pull the cap, inspect the mesh spacing against the NFPA 211 standard, and either clean and reset the original or source a compatible replacement with wider stainless mesh if the flue calls for it.
- Olympia Chimney multi-flue caps (MSC-series): The skirt-to-flue alignment on the MSC-1318 and MSC-1620 often drifts after five to seven winters of freeze-thaw cycling in Bristol County. The cap looks fine from the ground, but the skirt is no longer shedding water past the crown edge. We measure the flue spacing with a story pole, check for crown wash erosion underneath, and reinstall with a proper overhang or recommend a wider cap if the original was undersized from day one.
- Olympia Chimney galvanized economy caps: These were common on builder-grade installs in Taunton’s 1990s and 2000s construction booms. The galvanized coating fails at the seam welds first, not the top, so the rust is hidden until the cap is in your hands. We do not reinstall galvanized caps, period. We quote a stainless or copper replacement and show you the weld rot on camera before you decide.
- Olympia Chimney crown wash systems: The factory crown mix on some Olympia Chimney pre-fab chimney systems is poured thinner than site-built masonry crowns, which makes it more prone to spider cracking in Taunton’s coastal climate where salt air accelerates moisture intrusion. We do not slap sealant over active cracks. We grind to sound concrete, apply a bonding agent, and rebuild with a proper slope and drip edge, or specify a CrownCoat or HeatShield application if the substrate is sound enough to carry it.
- Olympia Chimney wind-load failures on cap mountings: The strap-tension brackets on older Olympia Chimney caps can fatigue where the stainless meets the masonry anchor point, particularly on taller chimneys in exposed Taunton neighborhoods like Whittenton or near the Taunton River. We replace the mounting hardware with through-bolt or masonry-screw systems rated for the actual wind exposure, not the original builder’s minimum spec.
Our Olympia Chimney Chimney Cap & Crown Process
- 1
Call and schedule: A live person answers, 24 hours a day. We ask about your Olympia Chimney model if you know it, the symptoms, and the chimney age. We give you a rough range before we book.
- 2
Level-2 camera inspection: Our technician arrives in uniform, background-checked, and photographs the cap, crown, and flue interior. You see the images on a tablet before any work is discussed.
- 3
Parts decision: We stock common Olympia Chimney cap sizes and carry DuraFlex, Gelco, and HeatShield materials for crown work. If your cap is under warranty and OEM replacement makes sense, we tell you. If a quality aftermarket cap fits better and costs less, we tell you that too. No manufacturer affiliation means no pressure either direction.
- 4
The repair: Cap jobs typically take 45-90 minutes. Crown repair or coating takes 2-4 hours depending on cure time. We protect your roof and landscaping, work cleanly, and run a post-repair camera pull to confirm draft and clearance.
- 5
Documentation and guarantee: You get photos, a plain-English verdict, and an invoice matching the upfront estimate. Every job carries our 90-Day Done Right Promise in writing, no arguing. If it’s not right, we come back.
What Olympia Chimney Chimney Cap & Crown Costs in Taunton
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Olympia Chimney single-flue cap replacement | $280-$420 | Stainless vs. copper, mesh gauge, flue diameter |
| Olympia Chimney multi-flue cap replacement | $380-$620 | Flue count, skirt depth, wind-load hardware |
| Crown crack repair (HeatShield or CrownCoat) | $340-$580 | Crack extent, flue count, need for bonding agent |
| Crown rebuild (partial, over sound base) | $580-$780 | Linear feet of crown, access difficulty, drip edge detail |
| Custom cap (non-standard flue or aesthetic match) | $520-$940 | Material, fabrication time, mounting complexity |
Steep roofs, buried chimneys behind dormers, or the need for scaffolding add labor time. We tell you before we start, not after we finish. Estimates are free. Call (774) 310-4281 for an exact quote on your Olympia Chimney system.
Why Taunton Homeowners Call Hearthstone Chimney Co. for Olympia Chimney Work
We have been sweeping and repairing chimneys in Taunton for over 42 years. Russell Haines learned the trade at Los Angeles Trade-Technical College and has spent the better part of two decades running sweeps here, including a stretch of older colonials near Taunton Green where the chimneys are as varied as the families living in them. He reads a flue the way other people read a room - quietly, thoroughly, and without missing much.
Our technicians are background-checked, uniformed, and carry the tools to handle Olympia Chimney, DuraFlex, HeatShield, and Gelco systems. Most jobs finish in one visit. The 90-Day Done Right Promise is in writing with no paperwork and no arguing. And a live person answers the phone every hour of every day, because a chimney problem does not wait for business hours.
If it’s worth burning wood in, it’s worth knowing the chimney is clear.
FAQs
No, installing a cap or performing crown repair does not void your factory warranty as an independent Olympia Chimney service provider, provided the work is done to manufacturer spec. We document our methods and use compatible parts. If your system is still under warranty and the failure is a covered defect, we will point you toward Olympia Chimney directly so you do not pay for what they should cover.
We can source OEM Olympia Chimney caps when they are the right choice, but we also carry quality aftermarket equivalents from Gelco and Famco that often fit better and cost less. We show you both options with the price difference and let you decide. No brand affiliation means no incentive to push one over the other.
If the crown has surface cracks but the concrete substrate is sound and the slope still sheds water, a HeatShield or CrownCoat application usually suffices. If the crown is crumbling, delaminating, or has lost its drip edge, partial rebuild is the honest answer. We make that call with a hammer tap test and camera inspection, not a guess from the driveway. Call (774) 310-4281 and we will show you exactly what we found.
Most single-flue cap replacements take under 90 minutes from ladder set to final photo. Multi-flue caps or jobs requiring crown repair underneath run longer, but we still complete most in a single visit. We do not leave you with a half-finished chimney and a promise to return next week.
Water enters the flue, freezes in the mortar joints, and opens gaps that let carbon monoxide leak or chimney fires start. In Taunton’s climate, a cracked crown worsens every winter. That said, we will tell you plainly if a repair can wait six months or needs attention before the next burn. Call (774) 310-4281 for a free inspection and an honest timeline.
Written by Russell Haines, Owner, Hearthstone Chimney Co. at Hearthstone Chimney Co., serving Taunton and nearby areas.